Filter By:

  • Show More Brands
  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Tools

Park Tool Professional Tool Kit
$759.95
An expanded and evolved set of our finest professional level shop tools that addresses the changing tool demands of modern bikes and their mechanics. The PK-3 includes over 70 of our best tools and was put together with versatility in mind. A great way to outfit a pro bench or to set up a fabulous home workshop, the PK-3 is an impressive set of tools that can help you perform hundreds of repairs and maintenance tasks. Kit Includes: ATD-1.2 Adjustable Torque Driver AWS-1 Three-Way Hex Wrench Set: 4, 5, 6mm AWS-3 Three-Way Hex Wrench Set: 2, 2.5, 3mm BBT-5/FR-11 Bottom Bracket/Cassette Lockring Tool for Campagnolo (12-tooth) BBT-9 Bottom Bracket Tool for 16-Notch External Bearing Cups BBT-32 Bottom Bracket Tool for 20 Notch Shimano and ISIS Drive BCB-4.2 Bike Cleaning Brush Set BO-2 Bottle Opener CBW-1 Open End Wrench: 8/10mm CBW-4 Open End Wrench: 9/11mm CC-3.2 Chain Checker CCP-22 Crank Puller for Square Taper Cranks CCP-44 Crank Puller for Splined Cranks CM-5.2 Cyclone Chain Scrubber CN-10 Professional Cable and Housing Cutter CNW-2 Chainring Nut Wrench CP-1 Chain Whip Pliers CT-3.2 Chain Tool DAG-2.2 Derailleur Hanger Alignment Gauge DCW-1 Double Ended Cone Wrench: 13/14mm DCW-2 Double Ended Cone Wrench: 15/16mm DCW-3 Double Ended Cone Wrench: 17/18mm DH-1 Dummy Hub DP-2 Threaded Dummy Pedal FR-5.2 Cassette Lockring Tool: Shimano, SRAM, Sun Race GP-2 Pre-Glued Super Patch Kit HCW-15 36mm/32mm Headset Wrench HMR-8 Shop Hammer HT-8 8mm Hex Tool MLP-1.2 Master Link Pliers NP-6 Needle Nose Pliers OBW-4 Offset Brake Wrench OM-1 Overhaul Mat PAW-12 12" Adjustable Wrench PH-1.2 P-Handle Hex Wrench Set PW-4 Professional Pedal Wrench RR-12 Tape Measure SBC-1 Spoke, Bearing and Cotter Gauge SCW-13 13mm Shop Cone Wrench SCW-14 14mm Shop Cone Wrench SCW-15 15mm Shop Cone Wrench SCW-16 16mm Shop Cone Wrench SCW-17 17mm Shop Cone Wrench SCW-18 18mm Shop Cone Wrench SCW-19 19mm Shop Cone Wrench SD-SET Shop Screwdrivers (Set of 4) SP-7 Side Cutter Pliers SW-0 Precision Spoke Wrench: .127" SW-1 Precision Spoke Wrench: .130" SW-2 Precision Spoke Wrench: .136" SZR-1 Shop Scissors TB-2 Emergency Tire Boots TL-1.2 Tire Lever Set TL-4.2 Tire Lever Set TWS-1 Torx Compatible Wrench Set
Park Tool Professional Travel And Event Kit
$749.95
A carefully selected set of some of our finest tools, housed in the BX-2 Blue Box Tool Case. The EK-2 contains more than 45 shop-level tools that fit into BX-2 Blue Box Tool Case with extra room for more tools and parts. Perfect for professional shop and team mechanics, as well as the home mechanic who wants the ultimate portable tool kit.
Park Tool Head Tube Reaming and Facing Set
$549.95
Proper frame preparation is very important. Park Tool's Head Tube Reaming and Facing Set combines reaming and facing of the head tube to create a perfect fit for most sizes of head cups. Includes: • 30.1 mm reamer (part #751.2) and four different size pilots (29.8mm, 30.0mm, 33.8mm, and 36.8mm) • 690 facer • Quick-release, quick-adjust feature: bottom portion slides off and on easily without threading SHIS terminology: The HTR-1 as stock will face frames of EC29, EC30, EC34 and EC37. It will ream frames of EC30. Accessories will allow service in other standards.
Park Tool Disc Brake Mount Facing Set
$449.95
The DT-5.2 is engineered and built to accurately face front or rear disc brake mounts so they are precisely aligned to the rotor. - Faces any IS Mount, Post Mount, or new Shimano Flat Mount, including low clearance, chainstay mounts - Telescoping axle adaptors allow use with any configuration of open or thru-axle dropouts and dropout widths (including Boost 110, Boost 148 and all fat bike axles) - Includes two facing cutters: IS Mounts Post and Flat Mounts - Includes storage case
Park Tool Professional Wheel Truing Stand
$399.95
The next generation of wheel truing stands! The TS-4 is made to accurately gauge any size wheel, with or without the tire installed. The TS-4 has many of the same features as Park Tool's famous TS-2.2 with some additional attributes to accommodate today’s wide variety of hub, wheel and tire combinations. - Both uprights move simultaneously to always keep wheel centered in the stand. - Accommodates axle widths from 75mm to 215mm - Direct action caliper arm adjusts to work with wheel sizes from 16" to 29"+ - Accommodates tire widths up to 5" with or without brake rotor mounted - Machined, welded, assembled and calibrated in our factory in St. Paul, MN - Precise accuracy, operation and adjustability - Built in thru-axle adaptors - Chrome plated and powder coated heavy gauge steel construction - Removable, replaceable nylon caliper tips to protect painted/anodized rims - Dial Indicator compatible (TS-2Di) (Sold separately) - Rotor gauge compatible (DT-3 & DT-3i.2) (Sold separately)
Quarq ShockWiz
$399.00
ShockWiz is a suspension tuning system for air-sprung mountain bikes that combines high-tech hardware with an intuitive smartphone app. It's lightweight, durable and powered by a long-lasting coin cell battery, ShockWiz automatically records and evaluates suspension performance every time you ride. The ShockWiz app displays straightforward adjustments that unite bike, terrain and riding style. ShockWiz works for all mountain bike riders, regardless of their experience or bike's intended use. It works on hardtail and dual suspension bikes, and for all levels of skill, speed, and terrain. With ShockWiz, you know exactly how your suspension is performing – and how to make it better. Features & Benefits: - Automated tuning recommendations - Shock tuning score - a snapshot of how well your suspension is set up for you - Works on hardtail and dual suspension bikes. Works for Cross-Country, Trail, All Mountain and Downhill. - Inexpensive, replaceable CR2032 battery lasts for months - Waterproof and dustproof - IP67 rating - Two alternative hoses (included) offer a range of fitting options - Smartphone app is compatible with Apple and Android phones Essential Details: - ShockWiz is designed for all mountain bike riders, regardless of your experience or bike's intended use. - You can tune for every riding style: Efficient (pedaling), Balanced, Playful or Aggressive. - Advice for air pressure, spring rate, compression and rebound is displayed in the intuitive smartphone app. - In the box: ShockWiz hardware, two hoses, rubber mounting boot and zip ties.
Park Tool 49.59mm Head Tube Reamer & Facer for 1.5-Inch Headset Standard
$329.95
The Park Tool 758.2 will ream and face the head tubes of bike using the 1.5" standard. The 758.2 is designed for use with the Park Tool HTR-1 or HTR-1B Headtube Facer and Reamer. Must also be used with the 750.2 Centering Cone Adaptor.
Park Tool Hub Bearing Press Set
$329.95
- The HBP-1 is designed to quickly and accurately press bearings into a wide variety of cartridge bearing-type bicycle hubs. - Quick release design for fast tool installation and removal - Includes two bearing presses and precision machined aluminum pilots, bushings, and spacers - Works with more than 20 different cartridge bearing sizes and multiple axle configurations
Wheels Manufacturing Inc. Sealed Bearing Press
$325.00
- Installs 16 bearing sizes including 3 different bottom bracket bearings: 2437, 6000, 6001, 6002, 6003, 6801, 6802, 6803, 6804, 6805, 6806, 6900, 6901, 6902, 6903, 6904 - Includes T-handles with Acme threaded rods, wood base with dowels for holding adapters, 16 bearing installation drifts, 3 "speed spacers" and 2 linkage offsets for full suspension bearing installation - Made in the USA
Park Tool Advanced Mechanic Tool Kit
$309.95
Designed specifically for the home mechanic who wants the best, the AK-3 Advanced Mechanic Tool Kit is a special collection of Park's finest tools, all housed in a tough toolbox. The AK-3 includes over 40 tools to work on a wide variety of current model bikes. A great set of tools a mechanic should not be without. Kit Includes: BBT-9 Bottom Bracket Tool for 16-Notch External Bearing Cups BBT-32 Bottom Bracket Tool for 20-Notch Shimano and ISIS Drive BO-2 Bottle Opener CC-3.2 Chain Checker CM-5.2 Cyclone Chain Scrubber CN-10 Professional Cable and Housing Cutter CNW-2 Chainring Nut Wrench CT-3.2 Chain Tool CWP-7 Compact Crank Puller DCW-1 Double Ended Cone Wrench: 13/14mm DCW-2 Double Ended Cone Wrench: 15/16mm DCW-3 Double Ended Cone Wrench: 17/18mm FR-5.2 Cassette Lockring Tool GP-2 Pre-Glued Super Patch Kit GSC-1 GearClean Brush HXS-1.2 Professional L-Shaped Hex Wrench Set MLP-1.2 Master Link Pliers PAW-12 12" Adjustable Wrench PW-5 Home Mechanic Pedal Wrench RR-12 Tape Measure SD-2 #2 Phillips Screwdriver SD-3 3mm Flat Blade Screwdriver SR-12 Chain Whip 5- to 12-Speed Compatible SW-0 Precision Spoke Wrench: .127" SW-2 Precision Spoke Wrench: .136" TB-2 Emergency Tire Boots TL-1.2 Tire Lever Set TWS-3 Torx Compatible 3-Way Wrench #349 Soft Bristle Soaping Brush
Park Tool Blue Box Tool Case
$304.95
The BX-2.2 features updated pallet configuration and storage options to help you keep your tools secure and easily accessible. The expanded custom designed tool pallets, including dual-sided pallet wings, are all housed in a virtually indestructible composite travel case. Designed and built for the traveling mechanic who demands the best! - Custom designed tool-holding pallets with loops and pockets - Folding, dual-sided pallet wings - Front tool pallet that stores securely inside during transport - Dent-proof composite shell built around an aluminum frame - Key lock - Nominal dimensions: 19" x 14.85" x 8.5" (48.25 cm x 37.7 cm x 21.6 cm), 13.2 lbs. (6 kg)
Park Tool Disc Brake Mount Facing Set
$295.33
• Engineered and built to accurately face front or rear disc brake mounts to be precisely aligned to rotor • Works on both post mounts and IS brake mounts • Low clearance to access chainstay post mounts • Works on 100mm width open dropout forks, 100mm width 15mm thru axle forks, and 20mm thru axle forks • Includes axles and skewers for 100/135mm open dropout spacing • Includes adaptors for thru axle frames in 135, 142, 150, and 157mm widths • Includes two different cutters: one for IS mounts, one for post mounts
Park Tool Blue Box Tool Case
$275.95
Keep your precious bicycle tools safe and secure when traveling to cycling events with Park's Blue Box Tool Case. It boasts a dent-proof composite shell supported by a tough, light aluminum frame. Inside are removable tool boards made with durable 600D ballistic nylon sewn to an ABS inner panel. You get 35 tool pockets and straps that accommodate a wide variety of tools. Plus, there's a lower compartment with adjustable partitions so you can customize your layout. The front board also detaches and hangs off the outside of the case so you can set up your full shop and see and access all your tools at once. And, since tools have that terrible tendency to wander when traveling, the Blue Box is lockable with both a combination and a key.
Park Tool Adjustable Crown Race Puller
$265.95
- Precision tool for quickly and easily removing the headset crown race from the crown race seat of the fork - Fully adjustable, allowing precise, independent positioning of each blade around the crown race for flexibility in fitting around crown race interferences - Works with 1,1-1/8,1-1/4,1.5" forks (suspension or rigid) and crown races with outside diameters up to 64mm - Accepts steerers up to 430mm - All steel construction for long life
Wheels Manufacturing Inc. Professional Bottom Bracket Tool Kit
$250.00
This is Wheels Manufacturing's new toolkit for installing, removing, and servicing Wheels Manufacturing bottom brackets. The kit includes their new bottom bracket socket tools for installing and removing Wheels Mfg. BB cups with the following spline patterns: 48.5mm 16-notch, 44mm 16-notch (may be compatible with FSA MegaEVO BB cups, Shimano, SRAM/Truvativ and FSA). It also includes sealed bearing extractors for 22mm, 24mm, and 30mm ID bearings. Includes - T-Handles with 1/2" threaded rod - (2) Universal bottom bracket drift (BB-OB) - (1) 48.5mm/44mm, 16-notch Bottom Bracket Socket - (1) 48.5mm, 16-notch Single Sided BB Socket - (1) 30mm ID sealed bearing extractor - (1) 24mm ID sealed bearing extractor - (1) 22mm ID sealed bearing extractor - (1) receiver cup - (1) 44mm receiver cup sleeve - (1) 42mm receiver cup sleeve - (1) 39mm receiver cup sleeve - (1) bearing pusher shaft - (1) 3/8" to 1/2" square drive adapter - Wood base
Park Tool Bottom Bracket Bearing Press Set
$209.95
The BBP-1 quickly and accurately installs bottom bracket bearings into press fit-type bottom bracket shells. - Quick release design for fast tool installation and removal - 12 precision-machined bushings (in 6 sizes) to fit these bottom bracket configurations: - 386EVO, BB30, BB86, BB90, BB92, BB95, BB121, BMX Mid, BMX Spanish, OSBB, PF41, Press Fit 24, Press Fit GXP, BBright Direct Fit, PF30 BBright Press Fit, Shimano Press Fit - Works on bottom bracket shell widths from 68mm to 150mm
Wheels Manufacturing Inc. Small Sealed Bearing Press
$200.00
Another indispensable tool for the professional bike shop, the Wheels Manufacturing Press-2 works with bearings that have an I.D. of 10mm or smaller (most front hub sealed bearing fall in this range). It features an aluminum base with 9 open bore and over axle adapters, and a quick release skewer. - Installs sealed bearing sizes 6801, 6802, 6803, 6900, 6901, R6, 688, 608, 609 - All parts are laser etched for easy identification
Wheels Manufacturing Inc. Over Axle Bearing Press Adapter Kit
$185.00
- Works in conjunction with Wheels Mfg sealed bearing press (BTI #WZ-9991) to install 10mm ID and larger bearings into hubs with shouldered axles, always pressing simultaneously on both the inner and outer race of the bearing and preventing damage during the installation process - Includes adapters for 12 different bearing sizes ranging from 10mm to 20mm: 6900,6000 (10mm ID); 6901,6001 (12mm ID); 6802,6902,6002 (15mm ID); 6803,6903,6003 (17mm ID); 6804,6904 (20mm ID) - Made in the USA
Park Tool Bearing Cup Press
$173.95
Park's HHP-2 accurately aligns and presses 1-, 1-1/8-, 1-1/4- and 1.5-inch headset cups into your frame's headtube. It features a quick-release design for fast tool installation and removal, extra-long handles for superior leverage and stepped bushings for precise cup alignment. This versatile tool also presses cartridge bearings and cups into one-piece bottom bracket shells and holds fixed-cup wrenches in place when removing or installing adjustable-type bottom brackets.
Park Tool Reamer
$142.95 - $173.95
Park Tool offers premium-quality reamers for nearly any bicycle standard. The reamers below are designed to quickly, accurately, and precisely ream headtubes when used with Park's Head Tube Reamer (HTR), ensuring a perfect headset fit and prfoessional-quality bicycle build. Choose the correct reamer for your application using the following information: - 751.2: This reamer is sized to 30.1mm. This allows a 0.1mm interference fit when pressing the 30.2mm headset of the “Euro” one-inch standard. - 754.2: This reamer is sized to 33.9mm. The allows a 0.1mm interference fit when pressing the 34.0mm headset of the 1-1/8" standard. - 788: This reamer is sized to 43.95mm. It reams head tubes to accept “internal” headset cups with 44.05 - 44.10mm O.D. (1-1/8 ZS standard). It is used with Park Tool's 690-XL Facing Cutter and 750 Centering Cone. - 738: This reamer is sized to 52.1mm. It is used to ream head tubes using the 1-1/2" integrated headset standard. It is used with Park Tool's 690-XL Facing Cutter and 750.2 Centering Cone Adapter. - 789: This reamer is sized to 55.95mm. It is used to ream head tubes to accept “internal” headset cups with 56.00–56.10mm O.D. (1-1/2 ZS standard). It is used with Park Tool's 690-XXL Facing Cutter and #750 Centering Cone Adaptor. - 799: This reamer is sized to 47mm. It is used for cutting the lower head tube on frames using an IS47 bearing for a 1-1/4" integrated headset. It cuts a 45-degree bearing set shoulder.
Park Tool Cutting Facer
$142.95 - $167.95
Park Tool has long provided some of the best cutting and machining tools in the bicycle industry. Their 690 Cutting Facers reflect their commitment to maintaining this high level of quality. Please read below for use and compatibility information specific to each size cutter: - 45mm (690): The 690 cutting facer is used on the HTR-1, HTR-1B, BFS-1, and BTS-1 cutting and facing tools. The facer has an outside diameter of approximately 45mm. - 57mm (690XL): The 690-XL is a larger version of the 690 facer for the HTR-1 Head Tube Reamer and Facer. It has a nominal outside diameter of 57mm. It may be used in conjunction with the 788 reamer. It is also used with the 767 Pilot or the 768 Pilot to face only the large diameter headtubes used with, "low profile," ZS-type headsets. - 65mm (690-XXL): The 690-XXL faces large headtubes. It has a nominal outside diameter of 65mm. Use the 690-XXL facer with the 750.2 Centering Cone Adaptor and 789 Reamer or 790 Pilot when facing head tubes with internal diameters of 55.95–55.90mm.
Bontrager Rhythm 35mm Hub Bearing Tool
$150.00
• Tool to service the bearings of Rhythm Pro/Elite and Line Elite rapid drive hubs • Blind-bearing puller design assists in removing the driveside 6807 bearing • Please visit the techsite for instructions on how to use • Steel
Park Tool Dial Indicator Gauge Set
$149.95
Park's Dial Indicator Gauge Set mounts to their TS-2 or TS-2.2 Truing Stand (sold separately). The set makes it easy to view and correct a wheel's lateral and radial run-out within a tolerance of .01mm. Compared to going by the gap between the truing stand pointer and rim, having gauges that put a number on the clearance makes wheel truing easier and more accurate.
Park Tool BB86/92 Shell Reamer
$134.95
- Used to ream and face BB86/92 bottom bracket shells to an ID of 40.98mm - Used in conjunction with HTR-1 head tube reaming and facing set (PK-6710), 750.2 centering cone adapter (PK-6735) and 690-XL facing cutter (PK-6730)
Park Tool Ratcheting Click-Type Torque Wrench
$132.99
With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The TW-6.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). Designed for higher torque settings for repairs and installation in the bottom bracket, cassette lockring and other areas that use a higher torque settings. For lower torque setting, see the TW-5. Comes with its own protective case. - 10–60 Newton meter range (88–530 Inch Pounds) - Adjustable in 0.25 Nm increments - Ratcheting 3/8" drive - Reads and registers for both left hand and right hand threading - Dial-adjust system allows desired torque setting to be preset - Calibrated to be accurate to +/- 4% - Length: 36.2cm (14.25")
Park Tool Socket and Bit Set
$119.99
The 37-piece SBS-3 from Park Tool is a comprehensive, shop-quality set of sockets, hex bits, and Torx compatible drivers selected specifically to tackle a wide variety of common bike repair needs. The SBS-3 also includes flat-faced sockets in common sizes for work on suspension forks. Ideal for use with Park Tool torque wrenches, the 3/8" drive bits and sockets are forged from tough, chrome vanadium steel and nickel chrome plated for lasting durability.
Park Tool Ratcheting Click-Type Torque Wrench
$115.99
With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The Park Tool TW-5.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). With a range of 2-14Nm, the TW-5.2 is designed for the lower torque settings that a shop or consumer would use for proper seat post, seat clamp and handlebar / stem applications. Comes with its own protective case.
Park Tool Ratcheting Metric Wrench Set
$115.99
World-famous Park Tool quality wrapped up in a great set of metric combination wrenches. The MWR-SET includes 6mm to 17mm wrenches with a 12-point two-way ratcheting box end. Forged from chrome vanadium steel, chrome-plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip. Strong, comfortable, and beautiful! - Includes 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, and 17mm wrenches
Park Tool Frame and Fork End Alignment Gauge Set
$110.95
Improperly aligned frame or fork dropouts can cause bent axles and quick-release skewers, as well as tracking and shifting problems. The Frame and Fork End Alignment Gauge Set quickly determines whether the frame or fork dropouts are aligned and parallel. If an error is detected, long handles and comfortable molded grips afford plenty of leverage for straightening. These Park gauges adjust to compensate for various hub widths from 100mm to 160mm, too.
Park Tool Home Mechanic Starter Kit
$110.95
A great way to start a tool collection! The perfect combination of tools to help the novice home mechanic clean, adjust, maintain, and do some basic repairs on their bike. The SK-3 includes more than 15 genuine Park Tool products plus a custom Park Tool toolbox. The SK-3 includes: AWS-11 Fold-Up Hex Wrench Set CC-3.2 Chain Checker CN-10 Professional Cable and Housing Cutter CT-5 Mini ChainBrute Chain Tool GP-2 Pre-Glued Super Patch Kit GSC-1 GearClean Brush MLP-1.2 Master Link Pliers PW-5 Pedal Wrench SD-2 Shop Screwdriver: #2 Phillips SW-7.2 Triple Spoke Wrench TL-1.2 Tire Lever Set #1622 Torx Compatible "L" Wrench
Bontrager Pro Adjustable Wrench
$100.00
Product details - Professional-grade tool developed in partnership with Knipex and made to last - Parallel jaws are significantly better alternative to traditional adjustable wrenches - Can replace entire sets of imperial and metric wrenches - 10:1 gripping power ensures no slipping or rounding of fasteners - Capacity of up to 1-3/8" and 35mm fasteners - Light enough to travel with, durable enough for daily use
Bontrager Pro Housing Cutter
$100.00
Product details - A professional-grade tool developed in partnership with Knipex and made to last - 7.5"/190mm length provides high leverage with minimum effort - Made from heavy-duty steel and additional induction hardening for tough, continuous use - Made in Germany - Features an integrated class-leading crimper for cable end caps and housing ferrules
KMC Digital Chain Checker
$99.00
KMC's digital ChainChecker is the most accurate tool for checking your chain’s elongation. - Measures up to 2.5mm elongation - Fits all chains including 11 speed - Handy electronic device - Stainless hardened metal body
Park Tool Professional Chain Scrubber
$98.95
A daily-use, shop version of Park Tool's world-famous CM-5.2 Chain Scrubber. The CM-25 features a super-tough die-cast aluminum case and handle, plus a unique brush/sponge replacement cartridge that makes it easy to keep it running smoothly and working properly. Park Tool's proven four-sided scrubbing action makes thoroughly cleaning chains quick and easy. A shop quality cleaner built to give years of constant use. - Proven chain scrubbing technology leaves chains sparkling clean - Durable A380 aluminum die cast case and removable handle - Dual-sided sponges and wicking pads to help reduce drips - Rotating brushes clean on all four sides of every link - Brush and sponge cartridge quickly and easily clicks in and out (RBS-25) - Locking cover with stainless steel hinge pins - Choose drip or immersion fluid application methods - 100% serviceable
Park Tool Thru-Axle Tap
$32.95 - $98.95
Frame and Fork Taps will become a lifesaver at some time for virtually every mechanic. These taps are made of high-carbon steel and are precision ground. Park Tool Frame and Fork Taps cut easily and fit conventional tap handles.
Avid Professional Disc Brake Bleed Kit
$98.00
Periodic brake bleeds are necessary to maintain consistent stopping performance, and Avid's Professional Disc Brake Bleed Kit has everything you need to keep your Avid Juicy, Code or Elixir hydraulic discs running strong. And, this pro version is designed to stand up to heavy use with high-volume syringes and steel fittings.
SRAM Pro Bleed Kit
$98.00
- Improved sealing and durability - New rotating metal hose fittings - High-volume hose with clamp - Longer lasting - Must-have for all mechanics - DOT 5.1 - NOT compatible with RockShox fork bleed kit
Park Tool Campagnolo Crank and Bearing Tool Set
$97.95
A complete tool set to work on both Campagnolo and Fulcrum Ultra-Torque and Power Torque crank and bottom bracket systems (each sold separately). The CBP-8 includes a beefed-up bearing and crank puller and all the fittings necessary to remove and install both systems. - Bearing Puller That Fits Both Power Torque And Ultra-Torque - Crank Puller For Power Torque - Bearing Setter For Both Power Torque And Ultra-Torque - Removal Adaptor For Power Torque Crank Bearings - Removal Protection Pads For Use With Carbon Cranks - Removal Protection Adaptor For Use With Aluminum Crank Arms - Crank Removal Extension Plug For Power Torque
Park Tool Frame and Fork Straightener
$96.95
Park Tool's Frame and Fork Straightener is a versatile and productive tool. Its open hook design enables it to straighten not only frames and forks, but also cranks and handlebars and it features vinyl coating on the hook and fulcrum pad to protect painted surfaces. The FFS-2's hook offers 8 inches of fore-aft adjustment and can fit a frame or fork tube of up to 1-3/4 inches in diameter.
Park Tool Crown Race Setting System — Oversized
$95.95
The CRS-15.2 uses two different insert rings to install bearing races on the 1.5-inch and 1-1/4-inch forks. The bearing surface is spared a direct hit by using aluminum inserts. Using a hammer, tap firmly on the end cap of the tube and seat the race into its proper place safely and accurately. Included extension allows work on fork steering tubes up to 425mm. - SHIS terminology: The CRS-15 services crown races in SHIS 33 and 40.
Giant 1/4
$95.00
- Designed for precise torque and to prevent carbon fiber component damage - 1/4" drive torque wrench with chromoly ratchet head - Chrome plated chrome vanadium Hex and Torx bits (Hex: 2,2.5,3,4,5,6mm Torx: T10,T25,T30) - 100mm extension bar included
Park Tool Snap Ring Pliers Set
$92.95
Designed and built with the specific needs of the bike mechanic in mind. The RP-SET.2 includes five professional quality pliers for internal snap rings and one for external snap rings. Pliers are made from forged, heat treated cro-moly steel with a return spring and vinyl dipped grips. RP-1: .9mm straight internal. Opens from 22mm down to 0 (tips touching) RP-2: 1.3mm bent internal. Opens from 22mm down to 2mm (center to center) RP-3: 1.3mm bent external. Opens from 2mm (center to center) up to 18mm RP-4: 1.7mm bent internal. Opens from 21mm down to 2mm (center to center) RP-5: 1.7mm straight internal; Opens from 25mm down to 0 (tips touching)
Park Tool Crown Race Setting System (1, 1-1/8 -inch)
$84.95
Quickly, safely and easily set your crown race with Park's CRS-1 Crown Race Setting System. It includes 6 different inserts (3 for 1-inch and 3 for 1-1/8-inch steerer tubes) that ensure full contact with the crown race for precision installation.
Park Tool Spoke Tension Meter
$84.95
The key to wheels that are strong and reliable is having spokes that are properly and uniformly tensioned. Park's Spoke Tension Meter accurately and reliably measures the absolute tension of each of the spokes in a wheel, as well as the relative tension between all the spokes in a wheel. It's easy to use, affordable and it works on nearly any bicycle spoke, no matter its diameter, material or shape.
Park Tool Crown Race Setting System (1.25, 1.5-inch)
$83.49
Quickly, safely and easily set your crown race on 1.5-inch steerer tubes with Park's CRS-15 Crown Race Setting System. Specifically engineered for oversized steerers, the CRS-15 comes with one setting tube and a 1.5-inch inset that ensures full contact with the crown race for precision installation.
Park Tool Centering Gauge
$79.95
Park Tool's Centering Gauge represents a dished rear wheel to assist in centering the TS-2.2 or TS-2 truing stands (each sold separately).
Park Tool Home Mechanic Bearing Cup Press
$79.95
Simple and economical, Park's Home Mechanic Bearing Cup Press is the perfect addition to your toolbox. With a few quick twists it easily installs all sizes of headset cups and one-piece bottom bracket cups.
Park Tool P-Handle Hex Wrench Set
$79.95
Engineered for fit, function, and leverage, these L-shaped shop-quality hex wrenches are a must have for every workshop. - High-torque, industrial steel wrenches - Straight hex shaft on the short side, ball end on the long side - Includes 2, 2.5, 3, 4, 5, 6, 8, and 10mm - Comfortable, ergonomically designed nylon handles fit perfectly in your hand - Durable wall/pegboard mount tool holder allows easy access and organization
Park Tool Metric Wrench Set
$77.95
Never be left looking for an errant wrench when you have Park's Metric Wrench Set. It includes 12 high quality Park metric wrenches from 6 to 17mm in diameter, featuring both box and open ends. They are all forged from chrome vanadium steel, then chrome plated for durability and dipped in Park Tool blue vinyl for outstanding comfort and ease of use.
Park Tool Shop Cone Wrench Set
$76.95
Park Shop Cone Wrenches are made of thin tool steel to fit the low-clearance adjusting nuts and cone flats on hubs and other bearing assemblies. Their special Y-heads put more material where it's needed for greater strength. Most applications require several cone wrenches, so Park gives you a whole set, featuring 13mm - 24mm, 26mm and 28mm wrenches to suit your repair needs.
Wheels Manufacturing Inc. Professional Universal Bottom Bracket Press
$75.00
Professional, shop-quality, version of the Wheels Mfg Universal Bottom Bracket Press, but with larger handles and brass inserts in the handle faces. Easy to use, this tool is made up of two machined aluminum handles, 1/2" threaded rod, and two machined aluminum drifts. Each drift is machined with multiple steps to fit common bottom bracket shell and bearing diameters listed below. No more searching for the correct size drifts and parts. Just match up the drift to your frame's BB shell size and your bottom bracket's bearing size and press. 1/2" diameter threaded rod resists bending, allowing for the cups to align and press in straight. Drifts can also be used as a frame bottom bracket shell sizing guide! - Machined aluminum handles and drifts - Brass inserts in the tool faces allow each handle to turn freely against drifts - Red anodized drifts and handles - Steps on drift are marked with diameter sizes - Zinc-plated 1/2" diameter threaded rod - Works with BB shells up to 132mm wide Fits: - BB30 (42mm) - PF30 (46mm) - BB86, BB92 (41mm) - BBRight (46mm) - BB386EVO (46mm) - Cannondale BB30A (42mm) - Cannondale PF30A (46mm) - Specialized Carbon OSBB (46mm) - Specialized Alloy OSBB (42mm) - TREK BB90, BB95 (37mm) - PF24 (41mm) - 22/24/30mm inner bearing diameters
Park Tool Derailleur Hanger Alignment Gauge
$74.95
The DAG-2.2 is an indispensable shop tool that can be used to both measure and straighten misaligned derailleur hangers solving a high percentage of shifting problems. - Gauge bar made of heavy gauge, chrome plated steel - Adjusts to fit 20" to 29"+ wheels - Replaceable threaded tip - Upgraded large inner shaft for added strength* - Tighter tolerances for improved accuracy* - Improved clearance and reach to fit more frame/hanger combos including low clearance thru-axle derailleur hangers* *Compared to DAG-2
Park Tool Adjustable Torque Driver
$72.95
Shop-quality, adjustable torque driver that limits torque applied to fasteners, preventing over-tightening and damage to lightweight components. The ATD-1.2 features all-metal internal construction with a comfortable, ergonomic composite molded grip. Each tool is assembled and calibrated at Park Tool's factory in Minnesota.
Park Tool P-Handle Torx Compatible Wrench Set
$70.95
Engineered for fit, function, and leverage, these L-shaped shop-quality Torx compatible wrenches are a must have for every workshop. - High-torque, industrial steel wrenches - Torx compatible drivers at each end - Includes T6, T8, T10, T15, T20, T25, T30, and T40 - Comfortable, ergonomically designed nylon handles fit perfectly in your hand - Durable wall/pegboard mount tool holder allows easy access and organization
Park Tool Tool Kaddie with Bench Mount
$67.95
Keep your most commonly used tools close at hand with this clever, multi-function tool holder. The TK-4T was painstakingly designed with pockets and holders for specific tool shapes and sizes as well as some generic storage areas. The Tool Kaddie rotates for easy access and is molded from a durable composite material. - Bench Top Mount sits firmly on any flat surface - Specific slots and holders for 3-way hexes, screwdrivers, P-Handles, pliers/cutters - Generic slots and holders to hold a wide variety of tools and small parts - Mounting location to directly attach HXH-2P or HXH-2T P-Handle Holders (sold separately) - Built-in receiver port for PTH-1 Paper Towel Holder (sold separately)
Park Tool Tool Kaddie with Stand Mount
$67.95
Keep your most commonly used tools close at hand with this clever, multi-function tool holder. The TK-4 was painstakingly designed with pockets and holders for specific tool shapes and sizes as well as some generic storage areas. The Tool Kaddie rotates for easy access and is molded from a durable composite material. - Stand Mount mounts to any Park Tool Professional Shop Stand (all versions of PRS-2, -3, -4, and -33) - Specific slots and holders for 3-way hexes, screwdrivers, P-Handles, pliers/cutters - Generic slots and holders to hold a wide variety of tools and small parts - Mounting location to directly attach HXH-2P or HXH-2T P-Handle Holders (sold separately) - Built-in receiver port for PTH-1 Paper Towel Holder (sold separately)
Park Tool Internal Cable Routing Kit
$66.95
Take the guesswork out of installing cables, wires and housing inside the frame. The IR-1.2 speeds the internal frame routing of electric wires, shift cable/housing, brake cable/housing and hydraulic tubing on carbon fiber, titanium, and aluminum frames. Kit includes four plastic-coated 250cm cables with attached magnets and unique fittings plus an external guide magnet to speed operation. Newly updated to include a dedicated E-tube Di2 cable connector that easily pulls through a 6mm frame hole. Opposite polarity magnets on cables seek and attach inside frame tubes, making it easy to route through frame entrances and exits. Works with any size frame including tandems. A true time and frustration saver!
Park Tool Master Chain Tool
$66.95
Park's Master Chain Tool is designed specifically to work with the tight tolerances and narrow profiles of 10- and 11-speed chains and all high-quality derailleur chains. It's made of tool steel for excellent durability and uses an integrated link pocket to ensure precise alignment. It also features perfectly contoured, cushioned handles for comfort and ease of use. This pro-level chain tool includes a removable anvil to peen Campagnolo 11-speed chains. (The CT-4.3 is not compatible with Wipperman chains.)
Park Tool Thru Axle Adaptors
$63.95
Park Tool's Thru Axle Adaptors make it possible to adapt all Park Tool Truing Stands to work with 12mm, 15mm, 20mm, and 25mm thru axle front wheels, as well as Cannondale Lefty wheels (each sold separately). The TS-TA also work with the rear 135mm thru axle hubs in the TS-2.2 and TS-3. The TS-TA when used in the TS-8, TS-25, TS-15, TS-7 or TS-5 will work with all rear thru axle hubs. For thru axle hubs greater than 135 (142, 150, 157, etc.) in the TS-2.2, use the TS-2TA Thru Axle Adaptors (sold separately).
Bontrager Pro Cable Cutter
$60.00
Product details - A professional-grade tool developed in partnership with Knipex and made to last - 8"/200mm length provides high leverage with minimum effort - Made from heavy-duty steel and additional induction hardening for tough, continuous use - Made in Germany - Perfect for cutting cables, cable ties, and many other materials
Page 1 of 7 Next page